MGB1970 » Restoration » Engine » Engine Teardown

email Dave Braun at dave@dbraun99.com (click here)

Always fun and exciting. Finding out what is in the engine.

1 Center Rocker Pedastal nuts and rockers removed 01	2 Pushrods and tappets removed and in order 01	3 Pushrods and tappets removed and in order 02	4 Head on bench showing valve side 01	5 Water Temperature sender
6 Cylinder Head studs 01	7 Cylinder Head studs 02	8 Double nutting to remove studs	9 Oil Sump 01	10 Oil Sump 02
11 Oil Pick-up Strainer	12 Removing oil pump cover	13 Bottom of engine 01	14 Oil pump laid out	15 Head studs removed
16 1 Cylinder	17 2 Cylinder	18 3 Cylinder	19 4 Cylinder	20 Scraping carbon off 20 over pistons 02
21 typical cylinder and piston after scraping	22 Rods marked 4 1 2 3	23 Engine disassembly	24 Fly wheel bolts and lock 01	25 Fly wheel bolts and lock 02
26 fly wheel bolts and locking washer	27 Fly wheel	28 Fly wheel teeth	29 Distributor mounting 01	30 Distributor mounting 02
31 Distributor mounting 04	32 Distributor mounting 03	33 An oil gallery plug	34 Distributor boss	35 distributor drive off cam shaft
36 Distributor drive well	37 double nutting oil pump studes	38 oil pump fasteners and gaskets including studs 01	39 oil pump fasteners and gaskets including studs 02	40 Engine tag and driven rivets
41 plug on opposite side of engine	42 rear engine plate	43 Rear Crankshaft seal retainer	44 Rear seal retaining plate and bolts	45 Rear engine plate 2
46 Rear crankshaft seal	47 Back Plate to Block hardware	48 Rear engine plate sealing plug	49 Front pulley bolt and washer	50 Front cramkshaft pulley
51 Timing cover and fasteners 02	52 Timing cover and fasteners 03	53 Timing cover and fasteners 01	54 Tming change tensioner 01	55 Tming change tensioner 02
56 Tming change tensioner 03	57 Timing chain tensioner with gasket and shim	58 Timing chain and gears01	59 Timing chain and gears02	60 Camshaft gear fasteners
61 canshaft locating pin 1	62 LH engine mount	63 Front engine plate and hardware	64 front engine plate	65 Oil cooler fitting 01
66 Oil cooler fitting 02	67 Oil filter adapter and bolt 01	68 Oil filter adapter and bolt 02	69 Oil pressure gauge line fitting	70 oil pressure regulator valve and gallery plug
71 Camshaft	72 Camshaft lobe wear 01	73 Camshaft lobe wear 02	74 Camshaft lobe wear 03	75 Camshaft lobe wear 04
76 Camshaft lobe wear 05	77 Camshaft lobe wear 06	78 Camshaft lobe wear 07	79 Camshaft lobe wear 08	80 camshaft locating pin 2
81 Camshaft on bubble wrap	82 Ready to remove crankshaft connecting rods and pistons	83 connecting rod big end clamps	84 Connecting rods and pistons 01	85 Connecting rods and pistons 02
86 Piston front down showing rod offset	87 using stud to wiggle off main caps	88 crankshaft removed	89 number four bearing is fine	90 number three bearing wth thrust bearings
91 number two bearing from bearing cap wth sharf in oiling hole 1	92 number two bearing from bearing cap wth sharf in oiling hole 2	93 number two bearing wth sharf filling oiling hole	94 RH engine mount	95 Crankshaft
96 Pistons connecting rods and crankshaft	97 Engine block stripped 01	98 Engine block stripped 02	99 Manifold attach hardware	100 Piston cleanup 01
101 Piston cleanup 02	102 Piston cleanup 03	103 Piston cleanup 04	104 Rocker pedastal studs	105 Tappet cover hardware
106 water pump to head hardware	107 Engine going in for machine work	108 Removing valve springs	109 Valve stem .082 groove	110 cleaning ring lands in pistons with broken ring
111 Chamfering threads in block 01	112 Chamfering threads in block 02	113 Wire wheel block 01	114 Wire wheel block 03	115 alternator bracket removed
116 Alternator bracket	117 LH engine mount with broken stud	118 mounts and bearing plates 00	119 mounts and bearing plates 01	120 mounts and bearing plates 02.

120 Images | Create web photo albums and photo books with Jalbum | Chameleon skin | Help